A better lathe too turn on?
ok soo i see how high speed lathe is good but its method expensive im 17 and im thinking buying a lathe sooner or later when i save up within few years i love turning its my life but i only do wood whats cheap and important wood lathe or high spped lathe i know high speed lathe have much more features
Answers:
It is not so much that a lathe will turn at a high speed. It has to do near how easy it is to change the speed and big a piece you can turn. Lathes that hold electronic (think push button) speed control are more expensive as are those that can turn large diameter stuff (greater than 12").
I have a Rikon mini lathe (not adjectives that small) with an extension. It has 5 speeds that you vary easily by moving the drive belts. It can handle a 12" diameter bowl and next to the bed extension, can take a spindle up to about 38" or so. A other made sturdy machine. Check with Amazon as you can frequently find sale and get cheap or free shipping. These usually run about $325 beside the extension costing about $90.
I use my lathe for turning pens, small bowls, ornaments etc. but can turn a table leg if needed. Source(s): TLD's go butchering wood
Wood lathes are simple tools & inwardly reason a modest one will do just as okay as an expensive one.
Speed is a function of what you are turning & high speed is not an advantage at adjectives.
Don't think I have ever used top speed.
As an example; hold a simple belt driven lathe for 40 years & if I had an expensive gear driven one would not be able to do any better work near it.
Would rather have upright turning tools & a means to keep them sharp fairly than a fancy machine.
Turning is more art than precision machine work & it comes down to how honourable you are rather than the machine.
Best regard
Keenan,
What part of the world are you in and what type of things are you turning?
The projects you are turning should determine the lathe. It sounds similar to you have fallen surrounded by love with the specs sheets from the catalog, rather than looked at the lathes realistically.
Realize most of the modern lathes on the market are very poorly made. A used (or contained by many cases antique) lathe will be much cheaper and vastly better made. Here in the northeast of the US, industrial equipment is busted up near a sledge hammer for scrap metal on a regular foundation. This is equipment of the quality that will never exists again. If the situation is the same where on earth you are, you can get the best quality ever made for a fraction of the tentative crap machine's price tag just by rescuing one of these from the neanderthals. Just something to consider.
In any armour the lathe should be subservient to the project spec. You will be disappointed if you allow "tool envy" to creep into the picture. Stick to what length of bed you need, what speeds you need, whether you necessitate a gap bed or end spindle, etc.
If you do failure up doing this for a living you will have a different lathe for each set of specs.
Good luck.
Related Questions:
Can I sticco over a cinder block wall short using the metal lathe?
How to insulate between brick exterior and plaster lathe walls?
Can a 4th-axis CNC mill essentially do CNC lathe turning?
Where can I find a replacement tailstock for a mini lathe?
Best Lathe for Bowl Turning?
Answers:
It is not so much that a lathe will turn at a high speed. It has to do near how easy it is to change the speed and big a piece you can turn. Lathes that hold electronic (think push button) speed control are more expensive as are those that can turn large diameter stuff (greater than 12").
I have a Rikon mini lathe (not adjectives that small) with an extension. It has 5 speeds that you vary easily by moving the drive belts. It can handle a 12" diameter bowl and next to the bed extension, can take a spindle up to about 38" or so. A other made sturdy machine. Check with Amazon as you can frequently find sale and get cheap or free shipping. These usually run about $325 beside the extension costing about $90.
I use my lathe for turning pens, small bowls, ornaments etc. but can turn a table leg if needed. Source(s): TLD's go butchering wood
Wood lathes are simple tools & inwardly reason a modest one will do just as okay as an expensive one.
Speed is a function of what you are turning & high speed is not an advantage at adjectives.
Don't think I have ever used top speed.
As an example; hold a simple belt driven lathe for 40 years & if I had an expensive gear driven one would not be able to do any better work near it.
Would rather have upright turning tools & a means to keep them sharp fairly than a fancy machine.
Turning is more art than precision machine work & it comes down to how honourable you are rather than the machine.
Best regard
Keenan,
What part of the world are you in and what type of things are you turning?
The projects you are turning should determine the lathe. It sounds similar to you have fallen surrounded by love with the specs sheets from the catalog, rather than looked at the lathes realistically.
Realize most of the modern lathes on the market are very poorly made. A used (or contained by many cases antique) lathe will be much cheaper and vastly better made. Here in the northeast of the US, industrial equipment is busted up near a sledge hammer for scrap metal on a regular foundation. This is equipment of the quality that will never exists again. If the situation is the same where on earth you are, you can get the best quality ever made for a fraction of the tentative crap machine's price tag just by rescuing one of these from the neanderthals. Just something to consider.
In any armour the lathe should be subservient to the project spec. You will be disappointed if you allow "tool envy" to creep into the picture. Stick to what length of bed you need, what speeds you need, whether you necessitate a gap bed or end spindle, etc.
If you do failure up doing this for a living you will have a different lathe for each set of specs.
Good luck.
Related Questions: