How do you repair hulking holes contained by plaster walls in that are lathe or nouns? boards bringing up the rear the plaster this is a ripened
i do not want to remove the old plaster just repair the walls where on earth the plaster has fallen out
Answers:
I grew up within a 100 yr old farmhouse beside the same problem. My father always stuffed the hole near newspaper and then mudded over it and consequently sanded it.
Easy job! I'm almost done restoring an 1908 home, here's a good contact to get u started:
http://www.thisoldhouse.com/toh/knowhow/repair/article/0,16417,1172537,00.html
simply appling mud to the surface will not work. If its a big hole you have to cut out a drywall patch to fill the hole, screw it contained by place, tape and float,texture and it will not be noticed. Easy to do, but unyielding to explain.
If you have lathes trailing the area that you want to repair, simply apply joint compound or mix up some plaster. The shared compound will have to be applied in a couple of high layers. Make sure the plaster around the patch area is not loose. If you do nut enjoy lathes, I have used Styrofoam cut to the size of hole. Just push it in and you can skim coat over it.
1) you can square out the hole by scoring the squared area beside a utility knife several times, afterwhich the plaster should break clean on the score lines, after light tapping.. Before you outline your square, you want to form sure the vertical sides are breaking on the studs, or 2 x 4s, in the wall, which are usually 16" apart; hopefully you can see one of them from the hole. After you've made your hole square, you're going to patch it with a piece of drywall of indistinguishable thickness, which will probably be 3/8'or 1/2 ". Then you're going to drive fasteners, nearly 12' apart minimum into the studs. Sink the fasteners slightly below the surface, so you can cover them up with shared compound.
Now, to the finishing, you need to apply a tape, to reinforce adjectives the joints; I reccomend fiberglass, it's self adhesive. Then you're going to apply mutual compound over the joint in three coats; near each coat the finish will get smoother, as long as you put fitting pressure on the knife(trowel) when you smooth the plaster. You don't want the coat of plaster to be thick, you want it to be flat. Bring each coat wider than the preious coat, after sand it prime it, paint it!
2) If the hole is no bigger than a small plate, then get a type of plaster call Durabond, which you mix with water. It comes within different setting times(20, 45, 90). It dries hard, and doesn't shrink much, which is what you want; you're making your own drywall. Remove any loose plaster before patching. After your Durabond is set, progress over it with two coats of a lighter plaster(Durabond is too hard to sand), only just as you would in the first method. Voilla! Source(s): Experience
Go to the local supply house and get the "mud" can't give attention to of the correct name, it is all equipped mixed up and ready to use. Only apply a small amount at a time and allow it to dry, like over hours of darkness and then apply some more to bring it up to the existing wall. Don't over do it as the more you put on the more you have to sand bad. Use a large trowel, flat not pointed. Has been a long time since I did it my self, 1955.
When sand use a small piece of 2x4 and tack the sand paper on it, will give you a better finish.
Related Questions:
What are the different parts of capstan lathe?
What does the permanent status 'swing' on a lathe scrounging?
What are types of coolant and coolant used for cnc lathe,grinding,honing,plateau honing?
How masses types of lathe chucks are here?
What is the swing of a lathe?
Answers:
I grew up within a 100 yr old farmhouse beside the same problem. My father always stuffed the hole near newspaper and then mudded over it and consequently sanded it.
Easy job! I'm almost done restoring an 1908 home, here's a good contact to get u started:
http://www.thisoldhouse.com/toh/knowhow/repair/article/0,16417,1172537,00.html
simply appling mud to the surface will not work. If its a big hole you have to cut out a drywall patch to fill the hole, screw it contained by place, tape and float,texture and it will not be noticed. Easy to do, but unyielding to explain.
If you have lathes trailing the area that you want to repair, simply apply joint compound or mix up some plaster. The shared compound will have to be applied in a couple of high layers. Make sure the plaster around the patch area is not loose. If you do nut enjoy lathes, I have used Styrofoam cut to the size of hole. Just push it in and you can skim coat over it.
1) you can square out the hole by scoring the squared area beside a utility knife several times, afterwhich the plaster should break clean on the score lines, after light tapping.. Before you outline your square, you want to form sure the vertical sides are breaking on the studs, or 2 x 4s, in the wall, which are usually 16" apart; hopefully you can see one of them from the hole. After you've made your hole square, you're going to patch it with a piece of drywall of indistinguishable thickness, which will probably be 3/8'or 1/2 ". Then you're going to drive fasteners, nearly 12' apart minimum into the studs. Sink the fasteners slightly below the surface, so you can cover them up with shared compound.
Now, to the finishing, you need to apply a tape, to reinforce adjectives the joints; I reccomend fiberglass, it's self adhesive. Then you're going to apply mutual compound over the joint in three coats; near each coat the finish will get smoother, as long as you put fitting pressure on the knife(trowel) when you smooth the plaster. You don't want the coat of plaster to be thick, you want it to be flat. Bring each coat wider than the preious coat, after sand it prime it, paint it!
2) If the hole is no bigger than a small plate, then get a type of plaster call Durabond, which you mix with water. It comes within different setting times(20, 45, 90). It dries hard, and doesn't shrink much, which is what you want; you're making your own drywall. Remove any loose plaster before patching. After your Durabond is set, progress over it with two coats of a lighter plaster(Durabond is too hard to sand), only just as you would in the first method. Voilla! Source(s): Experience
Go to the local supply house and get the "mud" can't give attention to of the correct name, it is all equipped mixed up and ready to use. Only apply a small amount at a time and allow it to dry, like over hours of darkness and then apply some more to bring it up to the existing wall. Don't over do it as the more you put on the more you have to sand bad. Use a large trowel, flat not pointed. Has been a long time since I did it my self, 1955.
When sand use a small piece of 2x4 and tack the sand paper on it, will give you a better finish.
Related Questions: