In buying a used lathe what should I look for.?
I've never used a lathe before. The one I will be checking out is a Craftsman older model. Also, where on earth should I look for the tools?
Answers:
i bought an prehistoric craftsman lathe and my only concern is that is uses mt1 drives and most everything very soon uses mt2 drives...(mt= morse taper)...checking for vibration is another thing...and does it allow outboard turning...probably not...it may be ok to swot up on but i am already looking for a better lathe and will get one someday...i mostly turn bowls so i may be able to catch by with a midi-lathe...
The chisels are call Craftsman Chisels, plus you might want some calipers and sand paper, just be paid sure everything is intact, no broken wires knobs feet or chuck. plug it within and put some wood in it and see if it can handle a nouns. does it have a foot pedal, speed settings and so on, but most importantly, you Need Safety glasses and a facade shield. and something to tie around your neck to keep wood chips from going down your shirt, No loose clothing,
Have a Craftsman lathe for about 40 yrs.
Probably the 36" w/ 6"swing & heavy tubular guardrail?
Simple machines & hard to abuse of break.
Very few things to run wrong or adjust.
All bearings are replaceable.
Aside from rust , not much else.
Can get rough tool sets at Sears or home centers.
Found that some Delta centers & accessories are interchangeable w/ Sears.
The older tools hold a black hardcoating & I think are a little better than up to date ones.
Plenty of turning sites & have found fine old tools surrounded by antique shops.
Just a few basic techniques to swot up .
Learn how to sharpen tools properly if you want to enjoy it.
Dont turn much anymore , but still find it relaxing.
Best regards
ask how much it's been used. most lathes sit around the shop summit dust and are in near unknown condition. if it's gotten lots of use you want to make sure the bearings are ok. spin it by paw and listen for a grinding noise (head and tail stock). make sure the tool rest moves freely and locks down safe and sound. see what accessories come with it. cup center, obverse plate, 3 or 4 jaw chuck calipers. centering square, etc.
lathe tools are expensive, about $25 respectively. you'll need gouges, skew chisels, a departure tool just to start. you might find some cheap ones at harbor freight, lowes, or home depot. but they will need frequent sharpening. sharpening lathe tools is another concern. it requires some skill if you try to sharpen by paw. you can invest in a sharpening system but that will cost you $150 or more.using dull tools is not a good hypothesis. dull tools will catch on the wood and tear chunks out of your turnings. unless your plan is to gross really pretty firewood you'll want to find a way to keep your tools sharp Source(s): e sure the tool rest moves freely and locks down safe and sound
Related Questions:
What is the swing of a lathe?
I purely get a craftsman 1/2 h.p wood lathe dont know much around it?
Where can I win a titanium hip orb token or something from a reject bin? Looking to lathe one for a rattan top
Where can I find a angelic cheap wood lathe?
Does anyone know how to turn drumsticks on a lathe?
Answers:
i bought an prehistoric craftsman lathe and my only concern is that is uses mt1 drives and most everything very soon uses mt2 drives...(mt= morse taper)...checking for vibration is another thing...and does it allow outboard turning...probably not...it may be ok to swot up on but i am already looking for a better lathe and will get one someday...i mostly turn bowls so i may be able to catch by with a midi-lathe...
The chisels are call Craftsman Chisels, plus you might want some calipers and sand paper, just be paid sure everything is intact, no broken wires knobs feet or chuck. plug it within and put some wood in it and see if it can handle a nouns. does it have a foot pedal, speed settings and so on, but most importantly, you Need Safety glasses and a facade shield. and something to tie around your neck to keep wood chips from going down your shirt, No loose clothing,
Have a Craftsman lathe for about 40 yrs.
Probably the 36" w/ 6"swing & heavy tubular guardrail?
Simple machines & hard to abuse of break.
Very few things to run wrong or adjust.
All bearings are replaceable.
Aside from rust , not much else.
Can get rough tool sets at Sears or home centers.
Found that some Delta centers & accessories are interchangeable w/ Sears.
The older tools hold a black hardcoating & I think are a little better than up to date ones.
Plenty of turning sites & have found fine old tools surrounded by antique shops.
Just a few basic techniques to swot up .
Learn how to sharpen tools properly if you want to enjoy it.
Dont turn much anymore , but still find it relaxing.
Best regards
ask how much it's been used. most lathes sit around the shop summit dust and are in near unknown condition. if it's gotten lots of use you want to make sure the bearings are ok. spin it by paw and listen for a grinding noise (head and tail stock). make sure the tool rest moves freely and locks down safe and sound. see what accessories come with it. cup center, obverse plate, 3 or 4 jaw chuck calipers. centering square, etc.
lathe tools are expensive, about $25 respectively. you'll need gouges, skew chisels, a departure tool just to start. you might find some cheap ones at harbor freight, lowes, or home depot. but they will need frequent sharpening. sharpening lathe tools is another concern. it requires some skill if you try to sharpen by paw. you can invest in a sharpening system but that will cost you $150 or more.using dull tools is not a good hypothesis. dull tools will catch on the wood and tear chunks out of your turnings. unless your plan is to gross really pretty firewood you'll want to find a way to keep your tools sharp Source(s): e sure the tool rest moves freely and locks down safe and sound
Related Questions: