Wood lathe tools needed?
I just purchased a wood lathe. I've never used a lathe before. Now my problem is where on earth to buy the tools and what would be the minimum amount of tools needed. There's such a wide variance on the net. Some are extraordinarily large and expensive others (like sears) look smaller. One is hardened steel, another with carbide tips. I will not be turning bowls or pen. I'll be making indian flutes. Suggestions?
Answers:
Just get some basic tools, resembling a parting tool and a few gouges, they are reasonably inexpensive so you should be able to get a complete set for around $30.00 unless you get top of the line later they could run as much as $100.00 a piece. The main difference you want to look for is the steel they are made from and how well they will hold the periphery, you want to spend most of your time turning and not sharpening. I have swiss made tools , they are the best but they are worth the money in my evaluation.
Do not need various turning tools for small hollow pieces like flutes.
A basic set is OK freshly to have around , but I'm thinking you will need finer , smaller tools for turning smaller diameter pieces w. any detail.
great tip from William B.
You can net own tools for special "profiles" or modify smaller tools for fine work.
Would invest in a drill chuck for the dead extremity so you can use the lathe to bore the holes down the flute body without turning the long bit.
Might make up a special jig or plug to hold the work while turning & boring.
I made plugs & holders out of hardwood for curious pieces that required turning before & after center material be removed.
Some are mounted to a small faceplate which is cheap.
They give something for the spur ,screw & dead centers to take while turning & allow removal & recentering if necessary without messing up finished ends.
You can achieve chucks that are adjustable ( like a metal lathe ) but they cost ....$$$$
A good grinder for shaping home made tools & sharpening will be more adjectives than a wide assortment .
Have to decide how to hold the work & If you plan on boring it out formerly or after the pice has been turned to shape.
Best regard
try starting with a 5-6 pc. set. check here:
http://www.woodcraft.com/
http://www.pennstateind.com/
avoid carbon steel, stick to glorious speed steel(HSS) M2. they dont need to be sharpened as often.
you will inevitability an 8" slow speed grinding wheel. about $100 or smaller amount at either of the above 2 sites. you dont want a high speed grinder.
as you go and get comfortable with the tools, and sharpening them, you will find out which individual chisels you like and stipulation.
Hope that helps. Good Luck, turning is a great hobby.
take some old files grind the ends to what you call for ,
[they make great lath tools ] and are cheaper Source(s): maintmman
Related Questions:
Anywebsite where on earth i can swot up just about lathe and how to use it?
Do you want to remove lathe and plasters?
Cnc lathes and mills are used for what exactly? any break this type of craftsmanship individual replaced by tech?
What is boring on the metal lathe?
What is a form tool used on a lathe?
Answers:
Just get some basic tools, resembling a parting tool and a few gouges, they are reasonably inexpensive so you should be able to get a complete set for around $30.00 unless you get top of the line later they could run as much as $100.00 a piece. The main difference you want to look for is the steel they are made from and how well they will hold the periphery, you want to spend most of your time turning and not sharpening. I have swiss made tools , they are the best but they are worth the money in my evaluation.
Do not need various turning tools for small hollow pieces like flutes.
A basic set is OK freshly to have around , but I'm thinking you will need finer , smaller tools for turning smaller diameter pieces w. any detail.
great tip from William B.
You can net own tools for special "profiles" or modify smaller tools for fine work.
Would invest in a drill chuck for the dead extremity so you can use the lathe to bore the holes down the flute body without turning the long bit.
Might make up a special jig or plug to hold the work while turning & boring.
I made plugs & holders out of hardwood for curious pieces that required turning before & after center material be removed.
Some are mounted to a small faceplate which is cheap.
They give something for the spur ,screw & dead centers to take while turning & allow removal & recentering if necessary without messing up finished ends.
You can achieve chucks that are adjustable ( like a metal lathe ) but they cost ....$$$$
A good grinder for shaping home made tools & sharpening will be more adjectives than a wide assortment .
Have to decide how to hold the work & If you plan on boring it out formerly or after the pice has been turned to shape.
Best regard
try starting with a 5-6 pc. set. check here:
http://www.woodcraft.com/
http://www.pennstateind.com/
avoid carbon steel, stick to glorious speed steel(HSS) M2. they dont need to be sharpened as often.
you will inevitability an 8" slow speed grinding wheel. about $100 or smaller amount at either of the above 2 sites. you dont want a high speed grinder.
as you go and get comfortable with the tools, and sharpening them, you will find out which individual chisels you like and stipulation.
Hope that helps. Good Luck, turning is a great hobby.
take some old files grind the ends to what you call for ,
[they make great lath tools ] and are cheaper Source(s): maintmman
Related Questions: