Would you buy a milling domestic device for $850?
I have an opportunity to buy a used, full sized milling machine. It is used. it's is not a Bridgeport but another key brand. I don't remember what which brand it is but it really looks serious. I doubt I'll see this opportunity again. It's used but not ancient or abused. Should I spring for it?
Answers:
only if you can see you getting more than 850 dollars out of it
On the face of it, that is an excellent price. But near are _many_things to consider:
a) How are the bearings, how tight is the bed and so forth. Bad bearings or a loose bed, anything loose, can cost considerable time, money and stab to correct. And if not corrected you will never be able to do precise work next to it.
b) What kind of motor is on it (voltage and phase). If it is not compatible with your available power, it will be an expense to replace Not the finishing of the world - just be aware of it.
c) What kind of tooling comes next to it? The cost of tooling may well exceed the cost of the machine, so the more that comes near it, the better the deal will be.
And, are you an experienced enough machinist to require such a component? Yes, they are _VERY_ nice to have and will allow you do do many things that smaller mills will not, but if the largest fragment you will ever do is no bigger than your fist and weighs maybe a couple of pounds you will own an expensive dust-and-rust gatherer in short order.
As an aside, a good quality vertical mill is an incredibly versatile and useful tool, and if you can maintain having one, that price is excellent if it is in well-maintained condition - especially if it comes beside a rotary table as part of the tooling. Source(s): Cut my teeth on Bridgports and South Bends.
$850 is an excellent price for a Bridgeport type milling machine in appropriate condition. However, don't forget to add in the cost of paraphernalia and installation which could cost you hundreds, even thousands more depending on what kind of work you want to do with it...
Most Bridgeport type machines are wired 460V.. You might want to check and see if your utility company and/or an electrical contractor can provide that for you...
My guess is that when you affix up the REAL cost of this machine you'll probably come to the conclusion that you can do without it...
Have a nice hours of daylight..
?
are you going to use it more than once ? I'd say yes...but for, why would you buy it....
hey those machines can cost a furtune to buy untried so i say ya u should
i would considering the fact that most newer ones are going to cost you more afterwards about 2 grand or so. But it is used, ask how dated it is, if it isn't any older then 5 years i'd lug it. But it's your choice! Hope this helped.
Related Questions:
You must evaluate a proposal to buy a current milling contraption.?
Mill tool Bridgeport Series II (4J head) shuts rotten every 15 minutes?
CRT Tube replacement surrounded by a CNC milling device control, Anyone beside CRT Knowledge?
How to obtain out melt contained by sugar from Food Mill (grinder machine)?
Can you use a milling contrivance to produce knife?
Answers:
only if you can see you getting more than 850 dollars out of it
On the face of it, that is an excellent price. But near are _many_things to consider:
a) How are the bearings, how tight is the bed and so forth. Bad bearings or a loose bed, anything loose, can cost considerable time, money and stab to correct. And if not corrected you will never be able to do precise work next to it.
b) What kind of motor is on it (voltage and phase). If it is not compatible with your available power, it will be an expense to replace Not the finishing of the world - just be aware of it.
c) What kind of tooling comes next to it? The cost of tooling may well exceed the cost of the machine, so the more that comes near it, the better the deal will be.
And, are you an experienced enough machinist to require such a component? Yes, they are _VERY_ nice to have and will allow you do do many things that smaller mills will not, but if the largest fragment you will ever do is no bigger than your fist and weighs maybe a couple of pounds you will own an expensive dust-and-rust gatherer in short order.
As an aside, a good quality vertical mill is an incredibly versatile and useful tool, and if you can maintain having one, that price is excellent if it is in well-maintained condition - especially if it comes beside a rotary table as part of the tooling. Source(s): Cut my teeth on Bridgports and South Bends.
$850 is an excellent price for a Bridgeport type milling machine in appropriate condition. However, don't forget to add in the cost of paraphernalia and installation which could cost you hundreds, even thousands more depending on what kind of work you want to do with it...
Most Bridgeport type machines are wired 460V.. You might want to check and see if your utility company and/or an electrical contractor can provide that for you...
My guess is that when you affix up the REAL cost of this machine you'll probably come to the conclusion that you can do without it...
Have a nice hours of daylight..
?
are you going to use it more than once ? I'd say yes...but for, why would you buy it....
hey those machines can cost a furtune to buy untried so i say ya u should
i would considering the fact that most newer ones are going to cost you more afterwards about 2 grand or so. But it is used, ask how dated it is, if it isn't any older then 5 years i'd lug it. But it's your choice! Hope this helped.
Related Questions: